WEAR RESISTANCE OF 304 AUSTENITIC STAINLESS-STEEL FRICTION WELDED JOINTS

JWAN KHALIL  MOHAMMED; RAMADHAN H  GARDI; DLAIR O.  RAMADAN

doi:10.26682/sjuod.2020.23.1.20

JWAN KHALIL MOHAMMED Dept.of Mechanical and Energy Engineering,Erbil Technical Engineering College, Erbil Polytechnic University, Kurdistan Region-Iraq
RAMADHAN H GARDI Dept. of Mechanicaland Mechatronics Engineering,University of Salahuddin, Kurdistan Region-Iraq
DLAIR O. RAMADAN Department of Technical Mechanical and Energy Engineering, Erbil Technical Engineering College, Erbil Polytechnic University, Erbil, Iraq

DOI: https://doi.org/10.26682/sjuod.2020.23.1.20

الملخص

In the present work, similar joint of AISI 304 austenitic stainless steel with a designed joint interface by 6 mm diameter and 6 mm depth, were processed by rotary friction welding route. Different parameters including forging pressure (192.4, 240.5, 288.6 and 384.8 MPa), friction pressure (192.4 MPa), frictional speed (560 RPM) and frictional time (1min) are examined. Pin on disc wear tester was used for wear test with counter disc SAF 2205 duplex stainless steel and cylindrical AISI 304 pin specimens. The surface roughness of duplex stainless-steel disc was measured. The wear rate in terms of weight loss were obtained for the pin specimens. The results of designed joint interface specimens showed better wear resistance than as-received. The variation of increasing wear loss with sliding distance has been found to be uniform for all the specimens. Further, it was noted from the experiments that the wear rate increased with increasing forging pressure.

التنزيلات

بيانات التنزيل غير متوفرة بعد.

السيرة الشخصية للمؤلف

JWAN KHALIL MOHAMMED، Dept.of Mechanical and Energy Engineering,Erbil Technical Engineering College, Erbil Polytechnic University, Kurdistan Region-Iraq

Department of Technical Mechanical and Energy Engineering, Erbil Technical Engineering College, Erbil Polytechnic University, Erbil, Iraq

المراجع

- Akbarimousavi, S.A.A., Goharikia, M., 2011. Investigations on the Mechanical Properties and Microstructure of Dissimilar cp-Titanium and AISI 316L Austenitic Stainless Steel Continuous Friction Welds. Mater. Des. 32, 3066–3075.

- Almanza-Casas, E., Perez-López, M.J., Steel, R., Packer, S., 2011. Evaluation of Mechanical Properties of 304L and 316L Stainless Steels Friction Stir Welded. Int. Offshore Polar Eng. Conf. 8, 530–533.

- Ates, H., Kaya, N., 2014. Mechanical and Microstructural Properties of Friction Welded AISI 304 Stainless Steel to AISI 1060 Steel AISI 1060. Arch. Metall. Mater. 59.

- Çaligülü, U., Dikbaş, H., Taşkin, M., 2012. Microstructural Characteristic of Dissimilar Welded Components (AISI 430 Ferritic-AISI 304 Austenitic Stainless Steels) by CO2 Laser Beam Welding (LBW). Gazi Univ. J. Sci. 25, 35–52.

- Chowdhury, M.A., Nuruzzaman, D.M., Roy, B.K., Dey, P.K., Mostafa, M.G., Islam, M.S., Mia, M.R., 2013. Experimental Investigation on Friction and Wear of Stainless Steel 304 Sliding Against Different Pin Materials. World Appl. Sci. J. 22, 1702–1710.

- Ganesan, M., Marimuthu, P., 2016. Experimental Investigation of Tensile Strength Behavior on Friction - Welded Austenitic Stainless Steel Grade 304L Joints. Int. J. Appl. Eng. Res. 11, 1251–1255.

- Kurt, A., Uygur, I., Paylasan, U., 2011. Effect of Friction Welding Parameters on Mechanical and Microstructural Properties of Dissimilar AISI 1010-ASTM B22 Joints. Weld. J. 90, 102–106.

- Majumdar, J.D., Ramesh Chandra, B., Manna, I., 2007. Laser composite surfacing of AISI 304 stainless steel with titanium boride for improved wear resistance. Tribol. Int. 40, 146–152.

- Mercan, S., Aydin, S., Özdemir, N., 2015. Effect of Welding Parameters on the Fatigue Properties of - Dissimilar AISI 2205-AISI 1020 Joined by Friction Welding. Int. J. Fatigue 81, 78–90.

- Rana, H.G., Badheka, V.J., Kumar, A., 2016. Fabrication of Al7075 / B4C Surface Composite by Novel Friction Stir Processing (FSP) and Investigation on Wear Properties. Procedia Technol. 23, 519–528.

- Thangarasu, A., Murugan, N., Dinaharan, I., 2014. Production and wear characterization of AA6082-TiC surface composites by friction stir processing. Procedia Eng. 97, 590–597.